Share

Our Products

Adhesives & Bonding Agent

Du Go

High Performance Adhesive slurry

scroll down

DU GO is Professional, Single-part, Superior adhesive slurry with high levels of adhesion and deformability, suitable for high-resistance laying with tacking technique or slurry key on fresh, cement–based mortars of homogeneous tiles, ceramic tiles of all types large-format paving slabs and stable natural stone.

  Download PDF

Areas of Application

Adhesive slurry specially made for cement mortar bed fixing all kind of poorly absorbent floor or non-absorbent floor.

Adjustability ≥ 30 min

Floors, for internal and external use

Suitable for ceramic, porcelain and single-fired tiles and stable natural stone

Features & Benefits

For high-resistance laying with tacking technique

Single-part

Superior-technology adhesive slurry

Method of Application

Preparation of Substrates

The screed must be compacted and braced to make it perfectly planar and suitable for laying covering materials. The degree of mechanical resistance must be adequate for the use of the flooring. Special care must be taken over the dosage of the cement and in the selection of the granulometry of inert fillers inn order to reduce the water/cement ratio and consequent hygrometric shrinkages.

Preparation and Application

Tacking Applications

  • DU GO must be applied with the tacking method directly on the cement based screed while it is still fresh. Spread a uniformly distributed quantity of product to create thickness of at least 2 mm thick
  • Moisten the tacking with a sprinkler and proceed to lay the covering materials
  • Beat down on the flooring with the appropriate equipment, moving in a direction perpendicular to that followed during laying and constantly making sure that the tiles have adhered properly to the substrate
  • Moisten a second time if necessary. Depending on customary technique and preference, hydration of the tacking can also be performed after laying the tiles

Slurry-key Application

  • Mix DU GO in a Container with clean water until a fluid, lump-free slurry key is obtained
  • Apply a uniform layer of at least 2 mm thick on the screed, using a smooth spreader or a trowel
  • Lay the covering materials and regulate with a rubber hammer to facilitate adhesion to the substrate without re-moistening

Technical Information

Appearance Gray/ White Ready-Mixed
Mixing water for use as slurry key 7 Ltr / bag 20 Kg
Temperature range for application From +5°c to 45°c
Adjustability ≥ 30min.
Foot traffic 34 hours

Grouting

7-14 days

Interval before normal use 14 days

Final Characteristics

Tensile adhesion on concrete After 28 days ≥ 1 mpa. En1348
Durability Test    
Adhesion after heat ageing ≥ 1 mpa. En1348
Adhesion after water immersion ≥1 mpa. En1348
Adhesion after freeze thaw cycles ≥1 mpa. En1348
Working temperature   - 40°c to +90°c  

Other Information

Precautions & Limitations

  • Do not use in screeds which have begun setting and are subject to continuous moisture rising
  • Perform laying and beating of tiles while the screed is still fresh
  • Protect against direct rain and freezing for at least 24 hours
  • Respect the structural joints
  • The temperature, ventilation and absorption of the substrate and covering
  • Materials may vary the workability and setting times of the tacking adhesive

Coverage

This shall depend on the nature and flatness of the surface and the method of application, but at 3 mm thickness it is approximately 2-3 Kg/m2 when using a solid bed trowel. For good coverage, it is vitally important that all surfaces should be clean, smooth plumb, level and free from defects and undulations.

Packing

10 Kg & 20 Kg bag.

Shelf life & storage

12 months in the original packaging in dry environment .

Quick Inquiry

Please enter name ! Please enter valid name !
Please enter 10 digits mobile no. ! Please enter valid mobile no. !
Please enter email id ! Please enter valid email id !